• Plan where you will put the designs. See if the sheet includes a plan to putting it together.
  • Peel the decals from the backing paper.
  • Smooth the designs to the wall.
  • To reposition them, just lift an edge and peel them off the wall.
  • Refer to the Cleaning Instructions to care for and store your wall stickers.


  • Plan the position of the whole design first. You can cut between parts of the design to make it easier to place in sections.
  • Scratch the designs through the tape layer with your nails and then peel back, ensuring all parts are “picked up”.
  • You need to place the pieces in the correct position the first time. Once adhered, smooth it to the wall.
  • Peel off the tape layer leaving the designs on the wall.
The top layer pick ups our decals

The top layer picks up the pieces



leaving the pieces on the wall!

leaving the pieces on the wall!

  • Equipment – a step ladder, a stanley knife, a spirit level, and maybe a second pair of hands. Make sure your hands are clean and dry. Inspect your wall and remove any picture hooks and any switch plates.
  • To remove the wallpaper from the tube (it can be tight), grab the corners from the inside the roll and, with the roll turned on it’s side, twist the panels until you feel movement – this should allow enough space to pull the panels out.
  • Start From the Left – start hanging panels on the left side of the wall, either according to the number written on the back, or just one by one. Take your time on this first panel, making sure it is level at the top. If the wall is adjoining another wall, you may need to slightly overhang Panel 1 on the left side and trim later, if the wall is not perfectly square.Shaynna Blaze putting up our wallpaper
  • Prepare To Stick –  lay the panel face down on a flat surface (somewhere clean) and peel back about 30cm of backing paper and fold it back sharply (so it stays out of the way). Do not let any debris stick to the adhesive.
  • Stick – line up the top edge of the wallpaper with the top of the wall and then stick it to the wall. If it is not square, peel it off and reapply.
  • Remove The Backing Paper – once in place, stick it to the wall. Carefully pull the backing paper down from behind the panel in stages, in a slow and even fashion. Let the wallpaper fall naturally into place, smoothing it to the wall with your hand in a down and outwards motion to remove any bubbles.
  • Wrinkles and Bubbles – all bubbles should just smooth out. If they don’t or a crease occurs, just peel up the panel and reapply rather than rubbing the print.
  • Additional Panels – align the next panel to the first panel, and remove the backing paper and stick to the wall as per the previous instructions.
  • If the design is not lining up, once the backing paper is removed from the panel, pull it away from the wall, drop it down 10cm from the top of the wall, align at eye level, smooth it onto the wall from the centre back to the top and to the bottom. Just keep the back of the panel from adhering to itself.
  • Trimming – when all the panels have been adhered, use a sharp stanley knife to remove any excess at the base of the wall. Carefully trim around the power points and light switches after pulling the plate off if necessary.
  • Keep Your Backing Paper and Tube – in case you decide to relocate your wallpaper, or move home or office, keep the backing paper and the tube to store your wallpaper in.
  • To reapply it to the backing paper without collecting debris on the back, you need to transfer it to the backing paper while vertical. Stick the backing paper to the wall with sticky tape (at the top and bottom) next to the panel you want to remove. Peel the whole wallpaper panel off the wall, move it across and place it onto the backing paper, getting it as lined up at the top and sides as possible. Just roll up the panel and carefully place it in the tube and protect the ends against damage with some bubble wrap.
  • Plan the position of the design first as it cannot be moved. Peel the design off the backing paper.
  • Place the design on the wall and smooth into place.
  • Wipe clean with a damp cloth.
  • To remove your chalkboard wall sticker, heat the design with a hair dryer in sections to remove it.
Chalkboard wall stickers

Use our chalkboard wall stickers with standard chalk and follow instructions to remove them without damaging your walls.

Note: Chalkboard products may cause paint to come off walls even if instructions are followed. We suggest applying to hard surfaces if you are concerned about the state of your wall.  Only for use with standard chalkboard and not liquid.

[vc_message message_box_color=”turquoise” css=”.vc_custom_1474796819037{background-color: #a1dbe4 !important;}”]Prepare Your Walls[/vc_message]

All our products require are that your walls are:

  • Dry
  • Clean – the cleaner they are, the more times our products can be reapplied
  • Plaster walls are painted: undercoat plus 2 top coats (any paint type)
  • Allow newly painted walls need at least 5 days to outgas before our products are applied
  • If you are putting up wallpaper or murals, you will need to remove the brackets around any power points, and remove and smooth over any hooks.